Sikkens Cetol WF 9810-46-25 (Formerly WF 761) Semi-Transparent, Satin-Matt Woodfinish


Sikkens Cetol WF 9810 - The revolutionary new semi-transparent wood finish. 

An easy to apply, brush and spray applied high durability translucent water-borne, satin-matt midcoat and finish for interior and exterior woodwork.  

Outperforms traditional oil based semi-transparent wood finishes. 

Available in existing Sikkens Cetol semi-transparent colours and the joinery range of 36 attractive shades from the Sikkens Cetol Natural Balance Colour Collection.  

Finish,  Satin-Matt (25% sheen)

Tested to DIN EN71 Part 3 Safety of Toys

£132.45 (excl VAT)
£158.94 (incl VAT)
£132.45 (tax excl.)
Colour choice
Please enter your required colour into the box below and click 'Save Colour Choice'.
  • 250 char. max

    Your Colour:

  • 1L
  • 2.5L
  • 10L
  • Semi-Matt

About Sikkens Cetol WF 9810-46-25 Semi-Transparent, Satin-Matt Woodfinish for new and old woodwork.

Cetol WF 9810 is a high performance waterborne, translucent, satin-matt,  base, mid and finish coat for interior and exterior wooden components and constructions.

It is used as a one pot, three coat system for both new woodwork and also renovation and correction of old paint systems.

  • High transparency
  • Good weather resistance
  • Good UV protection
  • Tested according to DIN EN 71 Part 3 "Safety of toys
  • Specially formulated for application by brush
  • Virtually eliminates blocking
  • Quicker hard drying
  • Improved impact resistance
  • Excellent flexibility 
  • Excellent weather resistance
  • Excellent adhesion to suitably base stained timber 
  • Moisture vapour permeable
  • Superb bright translucency  

Preparation and Application

The wood moisture content should be between 12 % and 15 %.

The selected wood, the design and the applied layer thicknesses should comply with current technical standards for example, all horizontal surfaces should be bevelled by  15 ° and all edges shall be rounded with a radius of at least 2 mm.

Old and loose coatings must be completely removed. Intact coating should be completely sanded smooth.

Fresh wood must be impregnated prior to coating, if necessary.

Open joints and cracks should be repaired using with Kodrin WV Joint Sealing Compound.

The substrates must be dry, free from dust and grease.

The selection and application of the coating, especially the colour shade, is important too. Dark coatings in the exterior may lead to an elevated surface temperature (up to 80 °C) in direct sunlight.


Clean equipment immediately after use with clean cold water or by a solution of Sikkens ST 830 and fresh lukewarm water.


Timbers which contain extractives i.e Oak, Larch or tropical woods can cause discolouring - these can appear after weathering.  


Be the first to ask a question about this product!

Question about the product

* Required fields
Send Question
All Colour Charts
Related products
Sikkens Cetol WF 771 Sikkens Cetol WF 771
Exterior Wood
£15.98 (excl VAT)
£19.18 (incl VAT)
£15.98 (tax excl.)
Sikkens Cetol WF 771 is a highly durable coating for exterior wood such as Pine, Spruce , Larch, Cedar, Oak, Teak and Accoya Retains the natural beauty of the wood Ideal for timber decking, garden furniture,...
£17.98 (excl VAT)
£21.58 (incl VAT)
£17.98 (tax excl.)
A colourless, water-based sealant to fill pores on end-grain areas to reduce damaging water ingress For interior and exterior timber components  Low-odour Quick drying Easy to apply   Part of the High Performance...
Exterior Wood
£13.70 (excl VAT)
£16.44 (incl VAT)
£13.70 (tax excl.)
A translucent, impregnating base stain for protection against bluestain, fungi and rotting on exterior wooden components. Impregnates and Primes in one coat. Available in clear (colourless) and a number of approved...
Recently Viewed



Need help? Call 01793 511537