New Guard - Guard GIP High-Build Zinc Phosphate Primer

Reference:
NGGIP

New Guard, Guard GIP is a high quality high build zinc phosphate primer with anticorrosion properties.

Quick to dry it is ideally suited mild steel, ferrous and suitably prepared non-ferrous metal.

Recommended topcoats, Guard FEB, Guard FES and two pack Guard MSP.  

Also suitable for general industrial finishing, agricultural machinery and earth moving equipment (ACE market).

Apply by spray, brush or roller. 

£40.88 (excl VAT)
£49.06 (incl VAT)
£40.88 (tax excl.)
Size
  • 5L
  • 20L
Finish
  • Matt
Colour
  • White
  • Black
  • Grey
  • Red Oxide
Close
Description

About Guard GIP, High-Build Zinc Phosphate Primer.

New Guard, Guard GIP is a high quality high build zinc phosphate primer with anticorrosion properties.

Quick to dry it is ideally suited mild steel, ferrous and suitably prepared non-ferrous metal.

Recommended topcoats, Guard FEB, Guard FES and two pack Guard MSP.  

Also suitable for general industrial finishing, agricultural machinery and earth moving equipment (ACE market).

Apply by spray or brush/roller. 

Preparation

Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.

Remove loose flaking or friable material. 

Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel

Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 

Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)

If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer.

Stainless Steel

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer.

Aluminium and Alloys

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer.

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions

Relative humidity should not exceed 80%. 

The surface temperature of the steel should remain at least 3ºC above the dew point.

Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats

Guard topcoats FEB,FES and MSP

Recommended Thinners 

Guard Solvent A or Guard Solvent F if application is by brush or roller.

Coverage Rates

Recommended Film weight: WFT 90-125µm

Theoretical coverage rate: 11m² per litre at a WFT 90µm

Application Methods

Guard GIP can be applied by the following methods.

Airless Spray: Yes

Conventional Spray: Yes

Brush: Yes for small areas only. Thin 0.2% by volume with Guard Solvent F

Roller: Yes for small areas only. Thin 0.2% by volume with Guard Solvent F

Application Guidance 

Airless Spray

Output fluid pressure at tip 12.0-16.00 Mpa, 

Tip Size 0.38-0.48 

Thin, up to 5% Guard Solvent A (Note thinning will reduce the film weight) 

Conventional Spray;

Output fluid pressure at tip 0.4 Mpa, 

Tip Size 1.8-2.0 

Thin with up to 10% added 3%-5% at a time.

Brush / Roller

Thin, up to 0.2% Guard Solvent F

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 125µm and 23ºC 

Dust Dry: 15 minutes

Recoatable: 45 minutes minimum

Hard Dry: 12 hours 

Full cure: 24 hours

Cleaning Tools and Equipment

Clean equipment with Guard Solvent A Thinner after use

% Volume Solids : 55%

VOC content : 382g / litre

Safe use

This product is formulated for professional use. 

Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.

Please contact us for the Health and Safety Datasheet.

Features
NGGIP
FAQS

Be the first to ask a question about this product!


Question about the product

* Required fields
Send Question
All Colour Charts
Related products
Recently Viewed
Exterior Wood
£96.81 (excl VAT)
£116.17 (incl VAT)
£96.81 (tax excl.)
Teknol Aqua 1410 Wood Prining Oil is an aqueous industrial wood preservative for new untreated wood formulated for exterior use such as windows and doors. The product protects the wood surface and the treated area...
Exterior Wood
£14.36 (excl VAT)
£17.24 (incl VAT)
£14.36 (tax excl.)
Teknos Anti Stain Aqua Primer 2901 is an industrial isolating spray primer. This specialist waterborne industrial primer inhibits hardwood tannins and knot staining.  It is a highly versatile, robust and easy to use...
Exterior Wood
£14.19 (excl VAT)
£17.03 (incl VAT)
£14.19 (tax excl.)
Teknos Teknoseal 4000 End Grain Sealer is a aqueous product for sealing of end grain of new wood designated for exterior use such as windows and doors.  Teknoseal 4000 dramatically reduces the vulnerability of end...
Exterior Wood
£189.53 (excl VAT)
£227.43 (incl VAT)
£189.53 (tax excl.)
A high performance mid-coat for timber, providing an isolating coating that works against wood extractives such as tannin that may discolour the paint finish Used or interior and exterior wood components. White only...

Menu

Settings

Need help? Call 01793 511537