Tikkurila Temaprime EE Fast Dry Primer

Reference:
TIK67

A fast drying, single pack anti-corrosion special primer.

Recommended for interior and exterior surfaces of ships above the waterline, storage tank exteriors, agricultural and industrial machinery where good adhesion and high corrosion resistance is required.

The product has MED (Marine Equipment Directive) certificate no VTT-C-11500-15-16 and is accepted for painting surfaces inside ships.

Matt finish

3 Litre & 10 Litre pack sizes

Available in any colour as well as Reddish Brown (TVT 4000) and Grey (TVT 4001) 

£43.86 (excl VAT)
£43.86
Colour choice
Please enter your required colour into the box below and click 'Save Colour Choice'.
  • 250 char. max
Size
  • 2.7L
  • 9L
Finish
  • Matt
Close
Description

About Tikkurila Temaprime EE Fast Dry Primer

Tikkurila Temaprime EE is a high performance anti-corrosion primer for steel, aluminium and zinc surfaces. It can also be used without any topcoat for steel surfaces in dry indoor areas.

A fast drying, one-component anti-corrosive special primer.

Used on surfaces where especially good anti-corrosive properties are required.

Adheres extremely well steel, aluminium and zinc.

Fast drying for rapid over coating.

Ideal for the  interior and exterior surfaces of ships above waterline, storage tank exteriors, agricultural machinery and other surfaces where especially good adhesion and anticorrosive properties are required.

Minimum damage from burning, welding and flame cutting.  

Preparation

Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.

Remove loose flaking or friable material. 

Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat

Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions
Relative humidity should not exceed 80%. 
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats
Overcoat with Temalac finishes

Recommended Thinners 
1006 or 1053 (slow) Thinners

Coverage Rates
Recommended Film weight:Minimum WFT 85µm Maximum 130µm
Theoretical coverage rate: 7.8-11.70m² per litre

Application Methods
Tikkurila Temprime EE can be applied by the following methods.

Airless Spray: Yes
Conventional Spray: Yes
Brush: Yes 

Application Guidance 

Airless Spray
Output fluid pressure at tip 120-160 bar, 
Tip Size 11-15 thou 
Thinning with  1006 or 1053 (Note thinning will reduce the film weight)

Brush 
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 50µm and 23ºC 
Dust Dry: 15 min 
Recoatable: 45 min

Cleaning Tools and Equipment
Clean equipment with 1006 Thinner after use

Volume solids : 45-49%

VOC content : 470g / litre

Safe use
This product is formulated for professional use only and by trained applcators.

Information on training can be found at https://www.safeusediisocyanates.eu

Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.

 

Features
TIK67
FAQS

Be the first to ask a question about this product!


Question about the product

* Required fields
Send Question
All Colour Charts
Related products
Tikkurila Temalac is a high performance, fast drying, single pack anti-corrosion single coat alkyd paint for steelwork Tikkurila Temalac is a high performance, fast drying, single pack anti-corrosion single coat alkyd paint for steelwork
ANY COLOUR
Metal Paints and Coatings
£41.11 (excl VAT)
£41.11
Tikkurila Temalac is a high performance, fast drying, single pack anti-corrosion single coat alkyd paint for steelwork. Excellent flow and application properties. Ideal for steel frameworks, agricultural machinery and...
Recently Viewed

Menu

Settings

Need help? Call 01793 511537