£93.81 (incl VAT)
ViterSeal 550 is a Two pack isocyanate free, high performance gloss finish.
A tough and weather resistant coating with excellent gloss and colour retention.
Indefinitely overcoatable
Suitable for maintenance, product manufacturing and new construction
Ideal for steelwork where isocyanates cannot be used
Available in any colour
£93.81 (incl VAT)
About ViterSeal 550 Two Pack Acrylic High Gloss Finish
ViterSeal 550 is a Two Pack Isocyanate Free, high performance gloss finish.
- A tough and durable gloss finish with excellent gloss retention.
- Indefinitely overcoatable and suitable for both manufacturing, maintenance and new construction
- Ideal for steelwork where isocyanates cannot be used
- Available in any colour.
Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material.
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.
Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas.
Mild Steel
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Phosphate Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat
Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.
Application Conditions
Relative humidity should not exceed 80%.
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.
Recommended Finish Coats
Overcoat with itself only
Recommended Thinners
1737 or 1048 Thinners
Coverage Rates
Recommended Film weight:Minimum WFT 94µm Maximum 113µm
Theoretical coverage rate: 8.8-10.6m² per litre
Application Methods
Protega Viterseal 550 High Gloss can be applied by the following methods.
Airless Spray: Yes
Conventional Spray: Yes
Brush: Yes
Roller: Yes
Mix Ratio: 2 Parts base :1 Part hardener
Pot life: 16 hours at 23ºC
Application Guidance
Airless Spray
Output fluid pressure at tip 1800psi,
Tip Size 13-19 thou (0.33-0.48 mm)
Thinning with 1737 (Note thinning will reduce the film weight)
Brush / Roller
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.
Please note: application by brush and roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
Drying times at a WFT at 94µm and 23ºC
Dust Dry: 1h
Recoatable: 16h
Hard Dry: 12h
Cleaning Tools and Equipment
Clean equipment with 1737 Thinner after use
% Volume Solids : 51-55%
VOC content : 450-494g / litre
Safe use
This product is formulated for professional use.
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.
For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.
Review this Product