ViterLac TF95 High Gloss CV Enamel

Brand:
Reference:
SPLTF95

ViterLac TF95 is a single pack, full gloss finish formulated for the Commercial Vehicle market.

Equally suitable for Agricultural, Construction and Earth moving equipment and for general use where an excellent gloss finish is required.

It has excellent flow, gloss and sag resistance and has excellent chemical resistance to petrol and hydraulic fluids.

Available in a wide colour range. 

£49.50 (excl VAT)
£49.50
Colour choice
Please enter your required colour into the box below and click 'Save Colour Choice'.
  • 250 char. max
Size
  • 5L
  • 20L
Finish
  • Gloss
Description

About ViterLac TF95  High Gloss CV Enamel

Protega ViterLac TF95 is a single pack, full gloss, high quality finish specially formulated for the Commercial Vehicle (CV) market.

  • Equally suitable for plant in the ACE (Agricultural, Construction and Earth moving equipment) market and for general use where an excellent gloss finish is required.
  • It has excellent flow, gloss and sag resistance 
  • Excellent chemical resistance to petrol and hydraulic fluids 
  • Available in a very wide colour range. 

Preparation

Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.

Remove loose flaking or friable material. 

Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel

Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 

Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)

If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat

Stainless Steel

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions

Relative humidity should not exceed 80%. 

The surface temperature of the steel should remain at least 3ºC above the dew point.

Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats

Overcoat with itself

Recommended Thinners 

1736 Thinners

Coverage Rates

Recommended Film weight:Minimum WFT 50µm2 Maximum 70µm2

Theoretical coverage rate: 14.3-20.0m² per litre

Application Methods

Protegalac TF95  can be applied by the following methods.

Airless Spray: Yes

Conventional Spray: Yes

Brush: Yes 

Roller: No

Application Guidance 

Airless Spray

Output fluid pressure at tip 1800-2500psi, 

Tip Size 11-19 thou (0.28-0.48 mm) 

Thinning if required with 1736 (Note thinning will reduce the film weight) 

Brush

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 50µm and 23ºC 

Dust Dry: 40 minutes

Recoatable:  2-3 hours

Hard Dry: Overnight 

Cleaning Tools and Equipment

Clean equipment with 1736 Thinner after use

% Volume Solids : 45-55%

VOC content : 368-388g / litre

Safe use

This product is formulated for professional use. 

Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.

Please contact us for the Health and Safety Datasheet

Features
SPLTF95
Reviews
No comments

Review this Product

  • Product Rating:
Colour Charts
FAQS

Be the first to ask a question about this product!


Question about the product

* Required fields
Send Question
Recently Viewed

Menu

Settings

Need help? Call 01793 511537