ViterLac PU90 PU modified High Gloss Enamel

Brand:
Reference:
SPLPU90

ViterLac PU90 is a general purpose urethane alkyd high gloss finish.

It has good weathering and durability retaining its gloss and colour over an extended period.

Quick to dry it is ideally suited for the finishing of structural steel over selected ViterPrime primers.

Used on agricultural machinery and earth moving equipment (ACE market).

Apply by brush or conventional spray. 

£49.75 (excl VAT)
£59.70 (incl VAT)
£49.75 (tax excl.)
Colour choice
Please enter your required colour into the box below and click 'Save Colour Choice'.
  • 250 char. max
Size
  • 5L
  • 20L
Finish
  • Gloss
Description

About ViterLac PU90 PU modified  High Gloss Enamel.

ViterLac PU90 is a general purpose urethane alkyd high gloss finish.

It has good weathering and durability retaining its gloss and colour over an extended period.

Quick to dry it is Ideally suited for the finishing of structural steel over selected ViterPrime primers.

Used on agricultural machinery and earth moving equipment (ACE market).

Apply by brush or conventional spray. 

Preparation

Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.

Remove loose flaking or friable material. 

Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel

Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 

Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)

If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat.

Stainless Steel

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat.

Aluminium and Alloys

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat.

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions

Relative humidity should not exceed 80%. 

The surface temperature of the steel should remain at least 3ºC above the dew point.

Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats

Overcoat with itself only

Recommended Thinners 

1006 Thinners

Coverage Rates

Recommended Film weight:Minimum WFT 62µm Maximum 88µm

Theoretical coverage rate: 11.4-16.0m² per litre

Application Methods

Viterlac PU90 can be applied by the following methods.

Airless Spray: Yes

Conventional Spray: Yes

Brush: Yes 

Roller: No

Application Guidance 

Airless Spray

Output fluid pressure at tip 1800-2500psi, 

Tip Size 11-19 thou (0.28-0.48 mm) 

Thinning with 1006 (Note thinning will reduce the film weight) 

Brush

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 50µm and 23ºC 

Dust Dry: 1-2h

Recoatable:  Overnight

Hard Dry: 2-3h 

Cleaning Tools and Equipment

Clean equipment with 1006 Thinner after use

% Volume Solids : 40%

VOC content : 420-460g / litre

Safe use

This product is formulated for professional use. 

Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.

Please contact us for the Health and Safety Datasheet.

Features
SPLPU90
Reviews
No comments

Review this Product

  • Product Rating:
Colour Charts
FAQS

Be the first to ask a question about this product!


Question about the product

* Required fields
Send Question
Recently Viewed

Menu

Settings

Need help? Call 01793 511537