£58.28 (incl VAT)
A single pack, fast drying alkyd primer specially formulated for the Commercial Vehicle (CV) market.
It can also be overcoated with single and two pack polyurethane finishes.
A single pack, fast curing, high build alkyd primer.
Compliant to PG6/34b (06) (below 540 gm/lt).
Excellent flow and wet edge characteristics.
Good hot spray application.
Outstanding corrosion resistance properties.
£58.28 (incl VAT)
About Viterprime VRP Compliant Primer for Vehicle Refinishing
ViterPrime VRP Primer is a single pack, fast drying alkyd primer specially formulated for the Commercial Vehicle (CV) market.
- Has excellent flow and wet edge characteristics with good hot spray application and outstanding corrosion resistance.
- Ideal for application by standard (unheated) airless or conventional spray and is used as a primer for steel and for GRP/fibreglass substrates.
- It can be overcoated and finished with Viterthane polyurethane finishes.
- Outstanding corrosion resistance properties and is Compliant to PG6/34b (06) (below 540 gm/lt)
Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material.
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.
Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas.
Mild Steel
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Phosphate Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat
Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.
Application Conditions
Relative humidity should not exceed 80%.
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.
Recommended Finish Coats
Overcoat with Viterthane topcoats
Recommended Thinners
1736 Thinners
Coverage Rates
Recommended Film weight:Minimum WFT 111µm - Maximum 333µm
Theoretical coverage rate: 3m² -9m² per litre
Application Methods
ViterPrime VRP can be applied by the following methods.
Airless Spray: Yes
Conventional Spray: Yes
Brush: No
Roller: No
Application Guidance
Airless Spray
Output fluid pressure at tip 2000-2500 psi,
Tip Size 13 thou
Thinning with 1736 Thinners (Note thinning will reduce the film weight)
Conventional Spray
Output fluid pressure at tip 60-80 psi,
Tip Size 1.0 - 1.4 mm
Thinning with 1736 Thinners (25% by volume)
Drying times at a WFT at 165µm and 23ºC
Dust Dry: 30 minutes
Overcoat: 45 minutes
Hard Dry: 2h
Cleaning Tools and Equipment
Clean equipment with 1736 Thinner after use
% Volume Solids : 45%
VOC content : 492-522g / litre
Safe use
This product is formulated for professional use.
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.
For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet
Review this Product