ViterLac OCF Anti-corrosion Gloss Primer/Finish

Brand:
Reference:
SVLOCF

A single pack one coat Anti-Corrosion One Coat Full Gloss Primer / Finish

Fast drying single coat system for blast cleaned steelwork for in-shop application

Provides a colourful, high gloss system in one coat

Formulated for airless spray application

Excellent build properties and hold-up on edges

Resistant to splashes of diesel and hydraulic fluid

Can be force-dried if required

£41.85 (excl VAT)
£41.85
Size
  • 5L
  • 20L
Finish
  • Gloss
Description

About ViterLac OCF Anti-corrosion Gloss Primer/Finish

A one coat Gloss anticorrosive alkyd primer/finish for steelwork.

It is a fast drying single coat system for blast cleaned steelwork for in-shop application.

  • Provides a colourful, high gloss system in one coat
  • Formulated for airless spray application
  • Excellent build properties and hold-up on edges
  • Resistant to splashes of diesel and hydraulic fluid
  • Can be force-dried if required
  • Readily available in a wide range of BS and RAL colours

Preparation

Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.

Remove loose flaking or friable material. 

Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel

Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 

Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)

If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat

Stainless Steel

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions

Relative humidity should not exceed 80%. 

The surface temperature of the steel should remain at least 3ºC above the dew point.

Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats

Overcoat with itself only

Recommended Thinners 

1006 Thinners

Coverage Rates

Recommended Film weight:Minimum WFT 91µm Maximum 182µm

Theoretical coverage rate: 6-4m² per litre

Application Methods

ViterLac OCF can be applied by the following methods.

Airless Spray: Yes

Conventional Spray: Yes

Brush: Yes 

Roller: Yes

Application Guidance 

Airless Spray

Output fluid pressure at tip 2000-2500psi, 

Tip Size 11-13 thou (0.28-0.33 mm) 

Thinning with 1006 (Note thinning will reduce the film weight)

Conventional Spray

The paint can be thinned to a viscosity of 23-35 secs through a BS B4 Cup

Typical atomising pressure at tip 40-60psi 

Brush

Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 120µm  and 23ºC 

Dust Dry: 1h 

Recoatable:  10h

Hard Dry: 16h 

Cleaning Tools and Equipment

Clean equipment with 1006 Thinner after use

% Volume Solids : 55%

VOC content : 400-449g / litre

Safe use

This product is formulated for professional use. 

Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.

Please contact us for the Health and Safety Datasheet

Features
SVLOCF
Reviews
No comments

Review this Product

  • Product Rating:
Colour Charts
FAQS

Be the first to ask a question about this product!


Question about the product

* Required fields
Send Question
Recently Viewed

Menu

Settings

Need help? Call 01793 511537