£56.51 (incl VAT)
A high performance single pack Vinyl Acrylic Anti-Corrosive Primer/Finish.
Formulated for application to Steelwork and Galvanised Steel
Can be applied to degreased new galvanising without the need for an etch primer
Available in a wide colour range
Ideal for items including gates, fences, street furniture and structural steelwork
£56.51 (incl VAT)
About ViterLac 305 Vinyl Acrylic Anti-Corrosive Primer/Finish
A high performance single pack Vinyl Acrylic Anti-Corrosive Primer/Finish.
- Ideal for Steelwork and Galvanised Steel
- Can be applied to degreased new galvanising without the need for an etch primer
- Highly moisture resistant
- Use for items including gates, fences, street furniture and structural steelwork
- Resistant to weak acids and alkalis
- Available in a wide colour range
Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material.
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.
Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas.
Mild Steel
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Phosphate Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat
Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.
Application Conditions
Relative humidity should not exceed 80%.
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.
Recommended Finish Coats
Overcoat with itself only
Recommended Thinners
1006 Thinners
Coverage Rates
Recommended Film weight:Minimum WFT 250µm Maximum 333µm
Theoretical coverage rate: 3-4m² per litre
Application Methods
ViterLac 305 can be applied by the following methods.
Airless Spray: Yes
Conventional Spray: Yes
Brush: Yes
Roller: No
Application Guidance
Airless Spray
Output fluid pressure at tip 2000 psi,
Tip Size 17-21 thou (0.43-0.53 mm)
Thinning with P100.... (Note thinning will reduce the film weight)
Conventional Spray
The paint can be thinned 15–20 %
Brush
Recommended for small areas of touch up or remedial work only
Thin as appropriate to achieve a smooth film flow.
Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
Drying times at a WFT at 250µm and 23ºC
Dust Dry: 15 minutes
Recoatable: 6h
Hard Dry 3h
Cleaning Tools and Equipment
Clean equipment with 1006 Thinner after use
% Volume Solids : 30%
VOC content : 583-623g / litre
Safe use
This product is formulated for professional use.
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.
For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet
Review this Product