Protega ViterPrime 035 High Build Zinc Phosphate Primer/Finish

Brand:
Reference:
SVP035

A single pack, quick drying, High Build Zinc Phosphate Primer for airless spray application to blast cleaned structural steelwork.

It can be used as a finish coat.

Matt Finish.

£32.55 (excl VAT)
£39.06 (incl VAT)
£32.55 (tax excl.)
Colour choice
Please enter your required colour into the box below and click 'Save Colour Choice'.
  • 250 char. max
Size
  • 5L
Finish
  • Matt
Description

About ViterPrime 035 High Build Zinc Phosphate Primer/Finish

A Single Pack, Quick Drying High Build Zinc Phosphate Primer for airless spray application to blast cleaned structural steelwork

  • Excellent build properties and hold-up on edges
  • Can be overcoated with ViterThane PLV and PLS two pack polyurethane finishes
  • Readily available in a wide range of Colour including BS and RAL
  • Can be used as a base coat for most thin film intumescent coatings 

Preparation

Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.

Remove loose flaking or friable material.

Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel

Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. Treat with a galvanising wash / mordant solution (Product Reference HSP 84/1) prior to application of the Primer Coat

Mild Steel

Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)

If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat

Stainless Steel

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. Etch prime with a Two Pack Etch Primer, (Product Reference 26/3) prior to application of the Primer Coat

Aluminium and Alloys

Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. Etch prime with a Two Pack Etch Primer, (Product Reference 26/3) prior to application of the Primer Coat

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions

Relative humidity should not exceed 80%.

The surface temperature of the steel should remain at least 3ºC above the dew point.

Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats,

Viterthane PLV, Viterthane PLS

Recommended Thinners

1006 Thinner

Coverage Rates

Recommended Film weight: WFT minimum 129µm, maximum 258µm

Theoretical coverage rate: 4-8m² per litre

Application Methods

Viterprime 035 can be applied by the following methods.

Airless Spray; Yes

Conventional Spray; No

Brush; Yes

Roller; No

Application Guidance

Airless Spray

Output fluid pressure at tip 2000 -2500psi,

Tip Size 17-19 thou (0.43-0.48 mm)

Thinning with 1006  (Note thinning will reduce the film weight)

Brush 

Recommended for small areas of touch up or remedial work only

Thin as appropriate to achieve a smooth film flow.

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT of 129µm at 23ºC

Dust Dry   15 minutes 

Hard Dry   90 minutes

Cleaning Tools and Equipment 

Clean equipment with 1006 Thinner after use

% Volume Solids :56-60%

VOC content : 412g / litre

Safe use.

This product is formulated for professional use.

Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.

Please contact us for the Health and Safety Datasheet

Features
SVP035
Reviews
No comments

Review this Product

  • Product Rating:
Colour Charts
FAQS

Be the first to ask a question about this product!


Question about the product

* Required fields
Send Question
Recently Viewed

Menu

Settings

Need help? Call 01793 511537